Jati Padang Pasar Minggu, DKI Jakarta      +62(21) 27656416      marketing@spektra-ms.co.id

SMS-putih
Spektra Megah Semesta
Services

Conventional NDT


NDT (Non Destructive Testing) plays a vital part in manufacturing, quality control and plant life management. It used in a wide range of industries including Aerospace, Oil & Gas, Manufacturing, Power Generation, Petrochemical, Transport and Civil Engineering.

UT-edit

Ultrasonic Inspection (UT)

UT uses complex electronic equipment. Any material which transmits mechanical vibrations can be tested. UT detects both linear and non-linear flaws and permits three dimensional interpretations. Evaluation is often difficult. The UT instrument converts electrical pulses into mechanical vibrations or waves. These waves travel across the tested specimen and reflect from flaws because of their different acoustic nature. The returning reflected waves are reconverted to electric energy and displayed as signals on a cathode ray tube (CRT). The position and size of these signals correspond to the position and size of the flaws.

radiography

Radiographic Inspection (RT)

Material density and its thickness set the limits of RT's usefulness. Internal flaws are RT's forte; its two dimensional views sometimes its drawback. RT uses penetrating radiation and works on the principle that denser or thicker materials will absorb more radiation and a sheet of radiographic film or image amplifier. A flaw presents anywhere within the specimen will absorb less radiation than the specimen itself. The flaw's presence and location will be indicated by an area of higher or darker exposure.

MPI-INSPECTION

Magnetic Particle Inspection (MPI) & DYE Penetrant Inspection (DPI)

The surface defect is difficult to be inspected using technology of RT or UT. Most of UT equipment have a dead zone area that could not inspect a defect that close to the surface. MPI & DPI give the solution to find more exact the surface defect.

Advance NDT


NDT (Non Destructive Testing) plays a vital part in manufacturing, quality control and plant life management. It used in a wide range of industries including Aerospace, Oil & Gas, Manufacturing, Power Generation, Petrochemical, Transport and Civil Engineering.

Long Range UT Inspection

The Services is to provide Ultrasound wave to check the integrity of the pipe along the line, to make clear information regarding the critical location along the pipe.

LONG-RANGE-UT_JUNI-2018-1

Ultrasonic Test Phased Array (UT-PA)

UT-PA is an advanced technology of conventional UT. Working principle of the UT-PA is the incorporation of convensional radiography and UT. Phased Array Probe composed of multiple piezoelectic elements, each element will emit and linear scan. The advantages of UT-PA is safe, effective broad beam, multiple beam configuration, high-density, increase productivity.

ut-pa

Eddy Current Inspection (EC)

EC instrument can be small and portable, or large multi-channel devices. The method is used only on electrically conductive materials. An energized electric coil induces a magnetic field into the tested specimen. The fluctuating magnetic field generates an electric eddy current. This change is electronically analyzed to provide flaw severity or material condition information.

 

 

edy

Our Other Services


NDT (Non Destructive Testing) plays a vital part in manufacturing, quality control and plant life management. It used in a wide range of industries including Aerospace, Oil & Gas, Manufacturing, Power Generation, Petrochemical, Transport and Civil Engineering.

MEI_PSV-INSPECTION

Pressure Safety Valve and PSV Testing Division

The Pressure Safety Valve and PSV Testing Division is responsible for the installation, maintenance, and testing of pressure safety valves (PSVs) on oil and gas rigs. PSVs are critical safety devices that protect personnel and equipment from overpressure events. The division's work ensures that PSVs are functioning properly and will operate as designed in the event of an emergency.

 Pressure Safety Valve
 PSV Testing Division

hydro

Ultrasonic Test Phased Array (UT-PA)

Phased array ultrasonic testing (PAUT) is a non-destructive testing (NDT) method that uses sound waves to inspect materials for flaws. PAUT is a relatively new NDT method, but it has quickly become one of the most popular methods due to its many advantages over other NDT methods.

 Hydrostatic Testing
 Cleaning
 Man Power Supply & Other Services

JUNI_BOROSCOPE

Inspection Engineer and Inspector for QA QC, Rotating, Electrical, Mechanical, Civil, General

 Pressure Safety Valve and PSV Testing Division
 Hydrostatic Testing, Cleaning, and Man Power Supply
 Inspection Engineer and Inspector for QA QC
 Inspection and Testing

holiday

Inspection and Testing

 Thermography Inspection
 Hardness Test  Positif Material Identification
 Holiday Inspection
 Cathodic Protestion
 Vacuum Test  Droop Cell

Rope Access Technique (RAT)


Rope Access Technique (RAT) is known as an acceptable methods to assist inspection activities at height and or difficult access. This method gives more assurance on safety performance, work volume capacity and wide range of accessibility and providing minimum impact

IMG_8266

Rope Access Technique (RAT)

Rope Access Technique (RAT) is known as an acceptable methods to assist inspection activities at height and or difficult access. This method gives more assurance on safety performance, work volume capacity and wide range of accessibility and providing minimum impact on other simultaneous activities.
Referring to working at height, the risk of such activities are possible injury or fatality as a consequence of fall from height. Therefore, PT. Spektra Megah Semesta has become a full member of IRATA seen September 2013. IRATA International is recognized as the world's leading authority on industrial rope access. Established in the UK in 1988 as the Industrial Rope Access Trade Association, an increase in membership worldwide led to the name IRATA International to reflect this.
In carrying out this rope access work we use a standard procedure that is IRATA ICOP September edition, IRATA General Requirement and IRATA Bye Laws February 2012. In carrying out this rope access work we use a standard procedure IRATA ICOP edition September, General Requirements and IRATA Bye Laws February 2012. All these procedures that we use for guidance in implementing safe work all rope access activities ranging from planning, management, competency and procurement of appropriate equipment for use.


 NDT Services
 Rise Inspection
 AWPI / Platform Inspection
 Blasting and Painting
 Cleaning Tank, Tower and Other

Rope Access Technique (RAT)

 Practical
 Very Safe
 Very Flexible
 Very Efficient in Total Price

Other Technique (Scaffolding)

 Require Many Workers
 Not Safe at High Level
 Time Consuming
 Not Always Possible to Install Scaffolding
 High Cost

Drilling Rig Inspection, Repair & Maintenances

Drilling-inspection-377x285-3
Drilling-inspection-377x285-4
  • Drilling Rig Derrick Mast Inspection (API4G) including bolt torque check.
  • Dropped Object Inspections, Survey & Corrective Action and awareness training.
  • EMAG Electromagnetic Inspection of Wire Rope.
  • Load Path, Hoisting Equipment, Drilling Handling Tools Inspection (API RP 8 B).
  • Lifting Gear Inspections & Survey (LOLER SI 2307) with LEEA Certified Inspector.
  • Top Drive System Inspection as per OEM.
  • Hull Inspections as per ABS Class.
  • Tubular Handling Equipment and Related item Inspection.
  • Anchor Winches and Associated Equipments Inspections.
  • Access Maintenances & Engineering Services (Rope Access by IRATA).
  • Derrick Building, Welding, Cutting, Repair, Maintenances.
  • Inspection and Maintenance of Electrical Installation in Hazardous Area with standard IEC 60079-17.
Drilling-inspection-377x285-2
Drilling-inspection-377x285-1

SMS 12 MONTHLY RIG ANNUAL INSPECTIONS SERVICES

List of Activities

SMS 6 MONTHLY RIG ANNUAL INSPECTIONS SERVICES

List of Activities
DSCN0065